# Quick Answer: Can I Use 14 Gauge Wire On A 20 Amp Breaker?

## What appliances need a dedicated circuit?

Dedicated circuits are highly recommended for all these devices:Electric oven, stove, or range.Refrigerator.Stand-alone freezer or chest freezer.Dishwasher.Microwave.Garbage disposal.Toaster oven.Countertop convection oven.More items…•.

## How many outlets can you put on a 20 amp breaker?

10 receptaclesOne rule of thumb is to assign a maximum draw of 1.5 amps to each receptacle, which allows for 10 receptacles on a 20-amp circuit.

## How many outlets can you put on a 14 2 wire?

14–2 wire is allowed for a 15 Amp circuit, and at 120 Volts, 15 Amps x 120 volts = 1800 volt-amperes. So that would allow ten (10) receptacles, you would probably derate that to eight (8) for an 80% safety factor.

## Can lights and outlets be on the same circuit?

Basic answer to your question of can a mixture of lights and receptacles be installed on a single circuit is yes.

## Can I use 14 gauge wire on a 20 amp circuit?

So yes, a 14 gauge wire will safely carry 20 amps, no problem. … You get 50% more current capacity with 12 gauge wire compared to 14 gauge wire. So the 12 gauge wiring would trip immediately if there was a dead short. A 14 gauge wire would not trip the breaker and it could smolder for a while.

## Can I mix 12 and 14 gauge wire?

Yes you can mix 12 and 14 gauge wire with a 15 amp breaker on the circuit. But it is not recommended because the next homeowner or electrician may be confused and put a 20 amp breaker on it again.

## Should I use 12 or 14 gauge wire?

If you’re wiring a circuit on which there are both lights and outlets, or you just aren’t sure which wire gauge to use, you can’t go wrong by choosing a 12-gauge wire. It’s not quite as flexible as a 14-gauge wire, and it costs a bit more, but it’s always a safe choice on a 15- or 20-amp circuit.

## How far can you run 12 gauge wire on a 20 amp circuit?

The total circuit would be about 60 -70 feet in length. It would only be supplying about 5 outlets and one light. It would be a light load, running small things, no heaters or med/large equipment. #12 provides reasonable performance up to about 100′ with general loads like you describe.

## How many outlets can I put on a 15 amp breaker?

eight lightsTypically, you can have no more than eight lights or electrical outlets on a 15-amp circuit. To determine the amp rating of a circuit, just look at the number on its breaker or fuse in your main electrical panel.

## What happens if you put a 20 amp breaker on 14 gauge wire?

If you plug in several devices on an outlet that total 20 amps, you will exceed the safe working capacity of the 14 gauge wire without tripping the breaker. (You may be under 15 amp for each individual outlet but between the two outlets on a duplex receptacle you can exceed the 15 amp rating of 14 gauge wire).

## What is the minimum gauge wire for a 20 amp circuit?

Amperage and Wire Gauge Building codes based on the National Electrical Code prohibit the use of 14-gauge wire anywhere on a 20-amp circuit. All wiring in such circuits must be 12-gauge or larger.

## What is 14 gauge wire used for?

General Purpose Cords14 – Wire12 – Wire6 – WireRecommended ForRecommended ForRecommended ForCommon residential wiring: Light fixtures, household receptacles.Common residential wiring: Light fixtures, household receptacles, small appliances.Large household appliances: Central air conditioning, electric furnace.4 more rows

## What is 12 gauge wire used for?

The following NEC regulations apply to Romex conductors:Wire Gauge or TypeRated AmperageCommon Uses14-2 Romex15 ALighting Circuits12-2 Romex20 ALighting and Outlet Circuits, refrigerator10-2 Romex30 AElectric water heater, baseboard heaters10-3 Romex30 AElectric Clothes Dryer4 more rows

## What gauge wire should I use?

Wire Gauge It’s counterintuitive, but the larger the number, the smaller the wire. The most common sizes you’ll find in residential work are 14-gauge and 12-gauge. Larger appliances such as electric stoves, electric water heaters, electric dryers and central air units will often use 10-, 8- or even 6-gauge wire.

## What size breaker do I need for 14 gauge wire?

14-gauge wire has a smaller cross-sectional area than 12-gauge and would overheat on a circuit controlled by a 20-amp breaker if the circuit was passing the maximum current. A 15-amp breaker, on the other hand, will trip before 14-gauge wire overheats.

## How many watts can 14 gauge wire handle?

2,400 wattsYou can load 2,400 watts onto your 14-gauge wiring for a 120-volt circuit.

## Should I use 15 or 20 amp outlets?

Standard 15-amp receptacles are suitable for typical household appliances, lamps and other accessories. A 20-amp receptacle is for heavy-duty appliances and power tools, such as air compressors. Residential garages occasionally have 20-amp receptacles to accommodate larger power tools.

## Can 14 2 wire be used for outlets?

for both 15A and 20A circuits the rule of thumb is a maximum of 10 receptacles per circuit. 15 amp breaker circuit 14/2 wire. … In general it’s “safe” to use a larger wire-size than required and the smallest fuse or breaker ampacity that the equipment will permit.